← Back to CVE intelligence
CVE intelligence

CVE-2026-76501

Vulnerability intelligence

Published Oct 7, 2026Sources checked Nov 21, 2026
9.8CRITICALCVSS out of 10
What this means

Review the available evidence

CVE-2026-76501 and is rated Critical severity with a CVSS score of 9.8. It is not in the current CISA KEV record we collected. That does not prove exploitation has not occurred.

What to do next

Remediation and response

Cisco Security Advisories guidance

Vendor revision: Oct 7, 2026

To remediate the vulnerabilities that were disclosed on October 7, 2026, Cisco strongly recommends that customers upgrade to the fixed software that is indicated in the advisories.

Cisco Security Advisories guidance

Vendor revision: Oct 7, 2026

Cisco has released software updates that address these vulnerabilities.

CISA KEVNot listedBased on the latest collected catalog
EPSS0.5%Estimated 30-day exploitation probability
Ransomware useNot markedCISA KEV ransomware field
Threat actors1Source-linked actor relationships
Overview

What is CVE-2026-76501?

A vulnerability in the Segment Routing over IPv6 (SRv6) Operation, Administration, and Maintenance (OAM) feature of Cisco NX-OS Software, known as NGOAM, could allow an unauthenticated, remote attacker to execute arbitrary code with root privileges or cause a denial of service (DoS) on an affected device.

This vulnerability is due to improper input validation of IP traffic when the NGOAM and SRv6 features are enabled. An attacker could exploit this vulnerability by sending crafted packets to an IP interface on an affected device.

A successful exploit could allow the attacker to execute arbitrary code with root privileges and could cause process crashes resulting in a reload and DoS condition.

Source: NVD

Official advisory

Configuration and update guidance

Cisco Security Advisories · Updated Oct 7, 2026

Affected products and configuration

These vulnerabilities affect Cisco Nexus 3000 Series Switches and Cisco Nexus 9000 Series Switches in standalone NX-OS mode if NGOAM is enabled and specific features are configured, as detailed in the following list:

  • CVE-2026-76485: To be affected by this vulnerability, the switch must have NGOAM enabled. That is the only requirement.

  • CVE-2026-76486: To be affected by this vulnerability, the switch must have NGOAM enabled and either Segment Routing over IPv6 (SRv6) or Network Virtualization (NV) Overlay enabled. NV Overlay also requires a VXLAN Ethernet VPN (EVPN) VXLAN Network Identifier (VNI) mapped to a Network Virtualization Endpoint (NVE) interface with at least one peer VXLAN Tunnel Endpoint (VTEP) learned (for example, BGP EVPN or an ingress-replication static peer).

  • CVE-2026-76501: To be affected by this vulnerability, the switch must have both NGOAM and SRv6 enabled.

Note: Cisco Nexus 3000 Series switches do not support SRv6, and only a subset of Cisco Nexus 9000 Series switches support SRv6. For more information, see Cisco Nexus 9000 Series NX-OS SRv6 Configuration Guide, Release 10.6(x).

Determine the Status of NGOAM

To determine whether a device is configured with NGOAM enabled, use the show feature | include ngoam command at the Cisco NX-OS CLI. The following example shows NGOAM enabled on a device that is running Cisco NX-OS Software:

switch# show feature | include ngoam
ngoam                  1          enabled 

Determine the Status of NV Overlay

To determine whether a device is configured with NV Overlay enabled, use the show feature | include nve command at the Cisco NX-OS CLI. The following example shows NV Overlay enabled on a device that is running Cisco NX-OS Software:

switch# show feature | include nve
nve                    1          disabled
switch# configure 
switch(config)# feature nv overlay 
switch(config)# show feature | include nve
nve                    1          enabled 

Determine the Status of the NV Overlay VXLAN EVPN VNI

To determine whether a device is configured with VXLAN EVPN VNI mapped on an NVE interface with at least one peer VTEP learned, use the following commands at the Cisco NX-OS CLI:

  • show running-config | begin "interface nve"

  • show nve vni

  • show nve peers

If all three commands return data, as shown in the following example, then the device may be affected by CVE-2026-76486.

switch# show running-config | begin "interface nve"
interface nve1
  source-interface loopback1
  member vni 160010 mcast-group 203.0.113.1
  member vni 160020 mcast-group 203.0.113.1
  no shutdown
  
switch# show nve vni
Interface  VNI      Multicast-group  VNI State
---------  -------- ---------------  ---------
nve1       160010   203.0.113.1      Up 

switch# show nve peers
Interface  Peer-IP      Peer-State
---------  ------------ ----------
nve1       192.168.2.1  Up

Determine the Status of SRv6

To determine whether a device is configured with SRv6 enabled, use the show feature | include srv6 command at the Cisco NX-OS CLI. The following example shows SRv6 enabled on a device that is running Cisco NX-OS Software:

switch# show feature | include srv6
srv6                   1          enabled
Workarounds and temporary mitigations

There are no workarounds that address these vulnerabilities.

If the NGOAM feature is not required, disabling it removes the attack vector and is a mitigation for all three vulnerabilities. Disable the NGOAM by using the Cisco NX-OS CLI command no feature ngoam in global configuration mode on a Cisco Nexus 3000 Series or 9000 Series Switch.

While this mitigation has been deployed and was proven successful in a test environment, customers should determine the applicability and effectiveness in their own environment and under their own use conditions. Customers should be aware that any workaround or mitigation that is implemented may negatively impact the functionality or performance of their network based on intrinsic customer deployment scenarios and limitations.

Customers should not deploy any workarounds or mitigations before first evaluating the applicability to their own environment and any impact to such environment.

Live Protect Shields

Cisco has released Live Protect shields for CVE-2026-76485, CVE-2026-76486, and CVE-2026-76501 to temporarily mitigate these vulnerabilities for Cisco NX-OS Software.

For information about Live Protect for Cisco NX-OS Software, see Cisco Nexus 9000 Series NX-OS Security Configuration Guide.

Note: Live Protect shields are temporary mitigations to bridge the gap until software updates can be scheduled. To remediate this vulnerability, upgrade to a fixed software release as noted in the Fixed Software section of this advisory.

Fixed software

Cisco considers any workarounds and mitigations (if applicable) to be temporary solutions until an upgrade to a fixed software release is available. To remediate these vulnerabilities and avoid future exposure as described in this advisory, Cisco strongly recommends that customers upgrade to the fixed software indicated in this advisory.

Cisco NX-OS Software

To help customers determine their exposure to vulnerabilities in Cisco NX-OS Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”).

If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories that the Software Checker identifies (“Combined First Fixed”).

To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to search for vulnerabilities that affect a specific software release. To use the form, follow these steps:

  1. Choose which advisories the tool will search-only this advisory, only advisories with a Critical or High Security Impact Rating (SIR), or all advisories.

  2. Choose the appropriate software.

  3. Choose the appropriate platform.

  4. Enter a release number-for example, 10.4(4) for Cisco Nexus 3000 Series Switches or 16.0(8e) for Cisco NX-OS Software in ACI mode.

  5. Click Check.

Exploitation status

The Cisco Product Security Incident Response Team (PSIRT) is not aware of any public announcements or malicious use of the vulnerabilities that are described in this advisory.

Read the collected advisory