Summary
Multiple vulnerabilities in the Operation, Administration, and Maintenance (OAM) feature of Cisco NX-OS Software, known as Next Generation OAM (NGOAM), could allow an unauthenticated, remote attacker to execute arbitrary code with root privileges or cause a denial of service (DoS) condition on an affected device.
These vulnerabilities are due to improper input validation of IP traffic when NGOAM is enabled. An attacker could exploit these vulnerabilities by sending crafted packets to an IP interface on an affected device. A successful exploit could allow the attacker to execute arbitrary code with root privileges and could cause process crashes, which could result in a reload of the device and a DoS condition.
Note: Feature requirements vary for each vulnerability. For details, see the Vulnerable Products section of this advisory.
Cisco has released software updates that address these vulnerabilities. There are no workarounds that address these vulnerabilities.
This advisory is part of a group of advisories. For a complete list of the advisories and links to them, see Cisco Advance Notification for Publication of October 7, 2026, Security Advisories. For further documentation of improvements and fixes in Cisco NX-OS Software, see Cisco NX-OS Software Security Hardening Release: October 2026.
Products covered
CVE-2026-76485: To be affected by this vulnerability, the switch must have NGOAM enabled. That is the only requirement.
CVE-2026-76486: To be affected by this vulnerability, the switch must have NGOAM enabled and either Segment Routing over IPv6 (SRv6) or Network Virtualization (NV) Overlay enabled. NV Overlay also requires a VXLAN Ethernet VPN (EVPN) VXLAN Network Identifier (VNI) mapped to a Network Virtualization Endpoint (NVE) interface with at least one peer VXLAN Tunnel Endpoint (VTEP) learned (for example, BGP EVPN or an ingress-replication static peer).
CVE-2026-76501: To be affected by this vulnerability, the switch must have both NGOAM and SRv6 enabled.
show running-config | begin \"interface nve\
show nve vni
show nve peers
Remediation
There are no workarounds that address these vulnerabilities.
If the NGOAM feature is not required, disabling it removes the attack vector and is a mitigation for all three vulnerabilities. Disable the NGOAM by using the Cisco NX-OS CLI command no feature ngoam in global configuration mode on a Cisco Nexus 3000 Series or 9000 Series Switch.
While this mitigation has been deployed and was proven successful in a test environment, customers should determine the applicability and effectiveness in their own environment and under their own use conditions. Customers should be aware that any workaround or mitigation that is implemented may negatively impact the functionality or performance of their network based on intrinsic customer deployment scenarios and limitations.
Customers should not deploy any workarounds or mitigations before first evaluating the applicability to their own environment and any impact to such environment.
Live Protect Shields
Cisco has released Live Protect shields for CVE-2026-76485, CVE-2026-76486, and CVE-2026-76501 to temporarily mitigate these vulnerabilities for Cisco NX-OS Software.
For information about Live Protect for Cisco NX-OS Software, see Cisco Nexus 9000 Series NX-OS Security Configuration Guide.
Note: Live Protect shields are temporary mitigations to bridge the gap until software updates can be scheduled. To remediate this vulnerability, upgrade to a fixed software release as noted in the Fixed Software section of this advisory.
Cisco considers any workarounds and mitigations (if applicable) to be temporary solutions until an upgrade to a fixed software release is available. To remediate these vulnerabilities and avoid future exposure as described in this advisory, Cisco strongly recommends that customers upgrade to the fixed software indicated in this advisory.
Cisco NX-OS Software
To help customers determine their exposure to vulnerabilities in Cisco NX-OS Software, Cisco provides the Cisco Software Checker. This tool identifies any Cisco security advisories that impact a specific software release and the earliest release that fixes the vulnerabilities that are described in each advisory (“First Fixed”).
If applicable, the tool also returns the earliest release that fixes all the vulnerabilities described in all the advisories that the Software Checker identifies (“Combined First Fixed”).
To use the tool, go to the Cisco Software Checker page and follow the instructions. Alternatively, use the following form to search for vulnerabilities that affect a specific software release. To use the form, follow these steps:
Choose which advisories the tool will search-only this advisory, only advisories with a Critical or High Security Impact Rating (SIR), or all advisories.
Choose the appropriate software.
Choose the appropriate platform.
Enter a release number-for example, 10.4(4) for Cisco Nexus 3000 Series Switches or 16.0(8e) for Cisco NX-OS Software in ACI mode.
Click Check.
CVEs in this advisory 3
What changed in later vendor updates
SecurityAlert records field-level changes from the point we begin following a bulletin. Earlier vendor changes may not have a field-by-field record.
- Added affected products: CVE-2026-76485: To be affected by this vulnerability, the switch must have NGOAM enabled. That is the only requirement., CVE-2026-76486: To be affected by this vulnerability, the switch must have NGOAM enabled and either....
- Removed affected products: Cisco Nexus 3000 and 9000 Series Switches NGOAM Remote Code Execution Vulnerabilities.
Updates
- Published by Cisco
The publication date reported by the vendor.
- Added to SecurityAlert
We collected the advisory from the official source.
- Confirmed at the source
Our collector saw this advisory during a later source check.